High Speed Emulator for J-Link V9 JLink USB JTAG Debugger Emulator for J-Link V11 V11P STM32F103C8T6 STM MCU V11

Product Description

Note:
keil pop-up "The connected J-Link is defective,Proper operation cannot be guaranteed......"
The driver version is too high. The solution is as follows:

* Copy the "JL2CM3.dll" and "JLinkARM" files to the keil/arm/segger directory to replace the original files and restart the keil software.

Please contact us if you need these documents.

There are three ways to manually update the KEIL DLL Method:
1: Upgrade the J-link program that comes with Keil.
2: Use the J-link driver that came with the previous version of Keil to replace the current one, that is, replace the... \Keil\ARM\Segger folder for the old version, so that the J-Link driver is also an old version of the inside, it will not prompt the J-Link update!
3: Uninstalled segger, downloaded the newer driver and reinstalled it, and copied jlinkarm.dll from segger/jlinkarm_v440 directory to keil/armgger directory. Used the MDK again, prompted for an upgrade, OK'd the upgrade, but this time after the upgrade, jlink did recognize it.

jlink enable disable serial port:
Enable the virtual serial port: jlink commander command console enter the command vcom enable
Close the virtual serial port: jlink commander command console enter the command vcom disable
After inputting the command and unplugging the device manager again, the COM port will come out!
Enable VCOM (virtual serial port) function
Enable VCOM (virtual serial port) function! Make sure your jlink is V9 or above.

Enter vcom enable to turn on the virtual serial port (last power-up effective)

If the connected probe does not show up, the connected probe is not enabled.

If the connected probe does not support vcom functionality, follow these steps

1. input power on

2. enter power off

3. type vcom enable

The following steps can be used

Pin 5 = J-Link-Tx (out), Pin 17 = J-Link-Rx (in)

Pin 5 = J-Link-Tx (out), Pin 17 = J-Link-Rx (in)

! Note

1. VCOM function can only be used in SWD mode, JTAG mode pin conflict!

2. Need to connect the VTref of the jlink to the 3v3 power supply.

3. vcom disable can disable vcom function.

Pros & Cons

Pros

Compatible with multiple popular J-Link debugger and STM MCU models
Wide 1.8-5.5V supply voltage range for broad microcontroller compatibility
Includes a fix for common Keil software errors with J-Link devices
Brand-new stock from manufacturer UICPAL

Cons

Incorrect product type labeling listed as a Voltage Regulator instead of a JTAG debugger emulator
No explicit warranty information provided in the product listing
Limited official product documentation included beyond the basic error fix note
Sourced exclusively from Mainland China, leading to potential international shipping delays

Common Questions

Which J-Link debugger models is this emulator compatible with?

This JTAG debugger emulator is compatible with J-Link V8, V9, V11, and V11P models, and works with STM32F103C8T6 and other STM MCUs.

What supply voltage range does this JTAG emulator support?

This emulator operates within a 1.8V to 5.5V supply voltage range, making it compatible with a wide variety of microcontroller boards.

What common software issue does the provided note address for this emulator?

The included note fixes the Keil pop-up error stating "The connected J-Link is defective" by replacing specific DLL and driver files in the Keil software directory.

What is the operating temperature range for this JTAG debugger emulator?

This emulator can operate reliably between -20°C and +70°C.

What shipping and order details apply to this emulator?

This product is sourced from Mainland China, supports custom orders, and is sold as new stock; specific minimum order quantities are not explicitly listed.

Specifications

Product Description

Pros & Cons

Pros

Cons

Common Questions